Part # CA2655L-3D & CA2655L-3P — 1973–1991 Chevy C30 Pickup Lower Control Arms
Installation Instructions

Please take the time to read these installation instructions and check the Hardware Parts List to be sure you have all the listed parts.

DJM parts should be installed by qualified mechanics. If you are not familiar with automotive repair, have the parts installed by someone with experience.

Please read the warranty information (blue page enclosed). Complete your Product Warranty Card and mail it to DJM Suspension.

Please take a few minutes to fill out your installation helper (back side of warranty). Accurate measurements before beginning installation will show any irregularities in your vehicle.

Hardware Parts List

Installation Steps

1. On the bottom of the pivot tubes are threaded holes for the grease fittings. With a 1/8” bit, drill through the bushing and sleeve to allow a path for grease. Remove any burrs on the inner sleeves and carefully thread in the grease fitting.
   
2. Line up the pins for the cross shaft and install using factory u-bolts. Install with the factory coil spring only.
3. Before installing the sway bar bracket to the control arm, loosen the bolts that hold the D-bushings to the frame under the bumper. Raise the lower control arm to ride height and install sway bar brackets, then tighten.
4. Grease all grease fittings.
5. Review all procedures and check that all parts are tight and installed correctly.
6. Replace wheels and torque lug nuts. Check that the tires will turn both ways without making contact.
   Critical Check: There must be absolutely no clearance problems between the wheels and tires, the spindle, the caliper, the control arms, or any other component before driving the vehicle.
7. Turn your steering wheel until it is straight. By sighting down the tires and truck you can get the toe fairly close. Adjustment is made with the tie rod ends — loosen nuts at the rack and turn the tie rod ends until the tires are in a straight line from front to rear. Tighten the nuts when done.
8. With the vehicle on the ground, measure the height of the front and record on the installation helper. Your measurements should be about 3” less than the before measurement.

Rev. #07-02 — www.DJMSuspension.com — Tech Line: (310) 538-1583

Part # HS1119-4 — 1973–1991 Chevy C30 Rear Hangers & Shackles
Installation Instructions

Please take the time to read these installation instructions and check the Hardware Parts List to be sure you have all the listed parts before beginning installation.

DJM parts should be installed by qualified mechanics. If you are not familiar with automotive repair, have the parts installed by someone with experience.

Please read the warranty information (blue page enclosed). Complete your Product Warranty Card and mail it to DJM Suspension.

Please take a few minutes to fill out your installation helper (back side of warranty). Accurate measurements before beginning installation will show any irregularities in your vehicle.

Hardware Parts List

• 2 — Spring Eye Hangers
• 2 — Shackles w/ Bushings (SH1012-2)
• 8 — 7/16” x 14 Nylock Nuts
• 8 — 7/16” x 14 x 1-1/4” Bolts
• 16 — 7/16” Flat Washers

Installation Steps

1. Working on one side at a time, remove the u-bolts holding the springs to the axle.
2. To keep the spring pack together while removing the overload, use two large C-clamps placed close to the center bolt on the leaf spring and tighten. Remove center bolt nut. Slowly loosen C-clamps and remove the upper overload spring. Clamp springs back together. Install center bolts and tighten. Remove C-clamps.
3. Verify that the spring center bolt is in the hole on the top of the axle before tightening u-bolts. When center bolt is in place, install u-bolts, bottom plate, and nuts. Tighten u-bolts.
4. Remove the two striker pad brackets attached to the frame.
5. Loosen and remove the two shackle bolts and remove the stock shackle. Test fit the new shackle and check for interference on the bottom of the bed. On some trucks a square bed brace will be in the way of the shackle — cut a notch in the brace wide enough for the bolts.
6. Remove the bolt holding the front of the leaf spring to the front spring hanger.
7. Remove the rivets holding the spring hanger to the frame. This can be done with an air chisel or by drilling out the rivets.
8. Mount your new DJM Spring Hanger in the original holes on the frame with the hardware provided. The gas tank may need to be moved to gain access to bolts on the driver side. Raise the axle so the front of the springs can be located in the new hanger. With factory bolts, attach the spring to the hanger and install nuts. Do not tighten nuts yet. (Some may find it easier to attach the spring to the hanger before bolting the hanger to the frame.) See Fig. 1 below.
9. Apply some grease to the bushings and inside sleeves, then attach the new shackle on the frame mount and bolt in place with factory bolts (Fig. 2). The shackle installs with bushings down and open side forward. The hole farthest from the bushing will lower the truck more than the closer hole. Raise the rear axle high enough to align the spring eye and shackle. Insert the remaining bolt and install nuts.
10. Install rear wheels and torque lug nuts. Remove jack stand and floor jack.
11. Check the height of the rear. You can change the height by moving the spring to the other hole in the shackle. When satisfied with the height, install new shocks. Tighten all bolts.
12. Take truck for a test drive. Record the complete height on the installation helper. Double-check all hardware.

Rev. #1-04 — www.DJMSuspension.com — Tech Line: (310) 538-1583